Steuerung zum Abfüllen nach Gewicht
Unser Kunde vertreibt Maschinen zum Absacken von Obst und Gemüse nach Gewicht. Der zu befüllende Sack hängt an einer Waage, die das Gewicht an ein Steuermessgerät der Tiger 320 Serie sendet. Über ein Förderband gelangt das Gut zum Sack. Nähert sich das Gewicht dem Sollwert, wird der Fördermotor vom Messgerät abgebremst. Wenn das Sollgewicht erreicht ist, berechnet das Messgerät automatisch - unter Einbeziehung des Bewegungsmoments der Waren - wann es die Einfüllklappe schließen und den Motor anhalten muss. Die Anzeige wechselt zwischen "BAGFUL" und dem Gewicht.
Wenn der Maschinenbediener dann den Sack aus der Halterung löst, wird das Messgerät automatisch benachrichtigt und erhöht seine Zähler für die Anzahl und das
Mehr »
Bubbler System Level Measurement
Bubbler systems are ideal for level measurement of open channel run off systems or duct and tank situations where debris, foam, steam, or surface turbulance makes standard methods of level measurement impractical.
Mehr »
DC Amps and Amp / Hr Controller
The customer has an application that requires to:
1. Display Amps from a DC shunt.
2. Display and control from dual totalized amp/hrs.
The amp/hrs from totalizer 1 operate Setpoint 1.
At programmed amp/hr intervals, a pump starts for a programmed On-time to pump replenishment chemicals to the plating tank.
When Setpoint 1 energizes, totalizer 1 resets to 0, the pump cycle starts, and the amp/hrs totalizer 1 restarts.
Mehr »
Dispense Tank Product by Weight
Our customer has a tank supported on a load cell and requires to dispense measured amounts of product from the tank.
Texmate installed a Tiger 320 Series DI-50E meter calibrated to indicate the product weight in the appropriate engineering units. The meter is installed with two remote push-button switches configured as TARE and TARE CLEAR. All non-application codes are blanked out. Relay 1 is connected to the tank outlet valve. The amount of product required is programmed into the meter at setpoint 1. Setpoint 1 is programmed with initial startup inhibit and relay latch OFF. _(See Setpoints & Relays Supplement (NZ201) for full details.)_
Mehr »
Dual Tank Level Annunciator-Controller
A bakery customer has two tanks containing a release agent that is sprayed into the baking trays. If the release agent runs out, the bread sticks to the trays. Two release agent drums, TANK 1 and TANK 2 are placed onto two independent load-cell platforms and both load cell outputs are connected to a dual load-cell input module installed in a DI-60AT controller.
1. On start up, TANK 1 valve is open.
2. When TANK 1 low level (set-point 1) operates, TANK 1 valve closes and TANK 2 valve opens.
3. The system is now operating from TANK 2.
4. TANK 1 is replaced, TANK 1 low level alarm is now OFF.
5. When TANK 2 low level alarm operates, TANK 2 valve is closed and TANK 1 valve is opened.
6. The sequence is repeated.
Mehr »
Abfüllen nach Gewicht
**Ersetzen Sie teure Motorsteuerungen für Abfüllanwendungen mit präziser digitaler Setzwertsteuerung.**
Kombinieren sie unser programmierbares DI-60A Steuermessgerät mit einem intelligenten Wiege-Eingabemodul für eine genaue und verlässliche digitale Prozesssteuerung.
Ein Behälter wird unter den Zapfhahn gestellt. Wenn der Startknopf gedrückt wird, wird die Anzeige auf Null gesetzt (tariert), das Ventil wird geöffnet und der Motor wird gestartet. Wenn der Setzwert 1 erreicht ist wird der Motor abgeschaltet und bevor Motor und Pumpe vollständig anhalten (aufgrund der Trägheit des Motors), wird das Abfüllgewicht (Setzwert 2) erreicht und das Ventil geschlossen.
Mehr »
Frost Protection Controller
The Frost Protection Controller is an integrated, low cost frost risk management system that reduces the risk of frost damage to an orchardist's crop. The system constantly monitors the orchard temperature using a Pt100 RTD sensor. When frost damage is imminent, the controller automatically initiates the timely delivery of water spray to the area at risk, raising the humidity level. Water delivery is maintained in a continuous cycle to the affected zones until the frost conditions have abated, ensuring better crop protection and conserving resources such as water and power.
Mehr »
Gasfüllstation
Unser Kunde hat eine Gasfüllstation, die das Befüllen von Gasbehältern mit unbekanntem Volumen erlaubt und die entsprechenden Kosten berechnet.
Das Messgerät automatisiert den Steuervorgang über ein Makro. Im Diagramm sind die beiden Ventile (Valve 1 und 2) GESCHLOSSEN (Ausgangsstellung). Wird der Schlauch an den Gasbehälter angeschlossen, wird das Makro über den Sicherheitsschalter (safety switch) ausgelöst. Ventil 1 wird GEÖFFNET, ein Referenzzylinder mit bekanntem Volumen wird gefüllt und das Messgerät speichert den anliegenden Druck, der vom Druckumwandler übermittelt wird.
Mehr »
Bewässerungssteuerung
Ein Winzer will sein Bewässerungssystem der aktuellen Wetterlage anpassen, um einerseits den Ertrag zu maximieren und andererseits die Kosten für die Bewässerung zu reduzieren. Dazu ist eine Wetterstation auf dem Weinberg, die Sonneneinstrahlung, Windgeschwindigkeit, Niederschlag und Lufttemperatur erfasst, mit einem Steuermessgerät der Tiger 320 Serie verbunden. Ein Makro, das auf dem Messgerät installiert ist, berechnet aus diesen Daten die Evapotranspiration.
Mehr »
Manual / Auto Station
In many industrial applications it is necessary to be able to control a device manually. Often a potentiometer or rotary switch is used, but this method can be too coarse and not easily repeatable. Texmate have developed a versatile and easy-to-use selection of manual stations, using their Tiger 320 Series controller, that produce an accurate, digitally controlled and scaled 4 to 20 mA or 0 to 10 V output.
Mehr »
Payload from a Weighbridge
Our customer operates a trucking company and requires a printed record of the weight of the load being carried.
Texmate installed a Tiger 320 series DI-50E meter with a permanently connected serial printer and two remote pushbutton switches. The meter is connected to the weighbridge, calibrated to read in the appropriate engineering units, and programmed for the remote tare functions with all non-application codes blanked out.
Mehr »
Press Control Peak Overload Application
The Texmate 320 Series bargraph controller samples at 50 times/second for this application. The press operates at 60 strokes/minute. The load cell output is rapidly changing up and down during each stroke of the press. The operator requires the display to be held at peak value for as long as practical.
Mehr »
Resin to Roving Ratio and Progress Monitoring System for the Composite/Fibreglass Industry.
Our customer requires the amount of resin and roving used during their manufacturing operation to be calculated, monitored, and recorded on a job-by-job basis, providing them with accurate costing and stock information.
Texmate installed a Tiger 320 Series controller and connected it to the resin feedline flow transducer and the roving weighing platform pressure transducer.
Mehr »
Intelligente Niederschlagsmessung für Bewässerungssysteme
Für den Freilandanbau in Gebieten mit geringem oder unregelmäßigem Niederschlag werden Systeme zur künstlichen Bewässerung benötigt. Die Niederschlagsmenge wird dabei meist mittels einer Kippwaage oder eines Durchflusssensors erfasst.
Steueraufgabe: Wenn der Niederschlag innerhalb einer bestimmten Zeit höher als X ist , dann unterbreche den Bewässerungszyklus. Wenn der Niederschlag höher als Y ist, dann unterbreche den Bewässerungszyklus für eine längere Zeit.
Mehr »
Abfüll- und Mischstation
Unser Kunde möchte zwei Chemikalien miteinander in einem vorgegebenem Verhältnis mischen, wobei die exakten Mengen variieren können. Durch ein Makro zur Berechnung der Zufüllmenge soll eine exaktere Mischung sowie eine Zeitersparnis erreicht werden.
Ein Behälter wird auf einer Waage platziert, die anschließend tariert (auf 0 gesetzt) wird. Die erste Chemikalie wird in den Behälter eingefüllt. Das Bedienpersonal gibt das gewünschte Mischverhätnis ein und drückt auf den Startknopf.
Mehr »
Wet and Dry Bulb Humidity Measurement and Control
Wet and dry bulb humidity measurement, using two temperature sensor probes, is perhaps the most reliable method of accurately calculating humidity for low temperature applications in industry today. Both sensors are mounted close together, with one designated the dry bulb sensor and the other the wet bulb sensor. The wet bulb is kept wet using a moistened cotton wick.
The wet bulb is cooled relative to the dry bulb by heat loss due to moisture evaporation from the wet bulb wick. The rate of evaporation is dependent on the ambient temperature and humidity.
Mehr »